#ifndef _SDE_DRM_H_ #define _SDE_DRM_H_ #include "drm.h" /* Total number of supported color planes */ #define SDE_MAX_PLANES 4 /* Total number of parameterized detail enhancer mapping curves */ #define SDE_MAX_DE_CURVES 3 /* Y/RGB and UV filter configuration */ #define FILTER_EDGE_DIRECTED_2D 0x0 #define FILTER_CIRCULAR_2D 0x1 #define FILTER_SEPARABLE_1D 0x2 #define FILTER_BILINEAR 0x3 /* Alpha filters */ #define FILTER_ALPHA_DROP_REPEAT 0x0 #define FILTER_ALPHA_BILINEAR 0x1 #define FILTER_ALPHA_2D 0x3 /* Blend filters */ #define FILTER_BLEND_CIRCULAR_2D 0x0 #define FILTER_BLEND_SEPARABLE_1D 0x1 /* LUT configuration flags */ #define SCALER_LUT_SWAP 0x1 #define SCALER_LUT_DIR_WR 0x2 #define SCALER_LUT_Y_CIR_WR 0x4 #define SCALER_LUT_UV_CIR_WR 0x8 #define SCALER_LUT_Y_SEP_WR 0x10 #define SCALER_LUT_UV_SEP_WR 0x20 /** * Blend operations for "blend_op" property * * @SDE_DRM_BLEND_OP_NOT_DEFINED: No blend operation defined for the layer. * @SDE_DRM_BLEND_OP_OPAQUE: Apply a constant blend operation. The layer * would appear opaque in case fg plane alpha * is 0xff. * @SDE_DRM_BLEND_OP_PREMULTIPLIED: Apply source over blend rule. Layer already * has alpha pre-multiplication done. If the fg * plane alpha is less than 0xff, apply * modulation as well. This operation is * intended on layers having alpha channel. * @SDE_DRM_BLEND_OP_COVERAGE: Apply source over blend rule. Layer is not * alpha pre-multiplied. Apply * pre-multiplication. If fg plane alpha is * less than 0xff, apply modulation as well. * @SDE_DRM_BLEND_OP_MAX: Used to track maximum blend operation * possible by mdp. */ #define SDE_DRM_BLEND_OP_NOT_DEFINED 0 #define SDE_DRM_BLEND_OP_OPAQUE 1 #define SDE_DRM_BLEND_OP_PREMULTIPLIED 2 #define SDE_DRM_BLEND_OP_COVERAGE 3 #define SDE_DRM_BLEND_OP_MAX 4 /** * Bit masks for "src_config" property * construct bitmask via (1UL << SDE_DRM_) */ #define SDE_DRM_DEINTERLACE 0 /* Specifies interlaced input */ /* DRM bitmasks are restricted to 0..63 */ #define SDE_DRM_BITMASK_COUNT 64 /** * Framebuffer modes for "fb_translation_mode" PLANE and CONNECTOR property * * @SDE_DRM_FB_NON_SEC: IOMMU configuration for this framebuffer mode * is non-secure domain and requires * both stage I and stage II translations when * this buffer is accessed by the display HW. * This is the default mode of all frambuffers. * @SDE_DRM_FB_SEC: IOMMU configuration for this framebuffer mode * is secure domain and requires * both stage I and stage II translations when * this buffer is accessed by the display HW. * @SDE_DRM_FB_NON_SEC_DIR_TRANS: IOMMU configuration for this framebuffer mode * is non-secure domain and requires * only stage II translation when * this buffer is accessed by the display HW. * @SDE_DRM_FB_SEC_DIR_TRANS: IOMMU configuration for this framebuffer mode * is secure domain and requires * only stage II translation when * this buffer is accessed by the display HW. */ #define SDE_DRM_FB_NON_SEC 0 #define SDE_DRM_FB_SEC 1 #define SDE_DRM_FB_NON_SEC_DIR_TRANS 2 #define SDE_DRM_FB_SEC_DIR_TRANS 3 /** * Secure levels for "security_level" CRTC property. * CRTC property which specifies what plane types * can be attached to this CRTC. Plane component * derives the plane type based on the FB_MODE. * @ SDE_DRM_SEC_NON_SEC: Both Secure and non-secure plane types can be * attached to this CRTC. This is the default state of * the CRTC. * @ SDE_DRM_SEC_ONLY: Only secure planes can be added to this CRTC. If a * CRTC is instructed to be in this mode it follows the * platform dependent restrictions. */ #define SDE_DRM_SEC_NON_SEC 0 #define SDE_DRM_SEC_ONLY 1 /** * struct sde_drm_pix_ext_v1 - version 1 of pixel ext structure * @num_ext_pxls_lr: Number of total horizontal pixels * @num_ext_pxls_tb: Number of total vertical lines * @left_ftch: Number of extra pixels to overfetch from left * @right_ftch: Number of extra pixels to overfetch from right * @top_ftch: Number of extra lines to overfetch from top * @btm_ftch: Number of extra lines to overfetch from bottom * @left_rpt: Number of extra pixels to repeat from left * @right_rpt: Number of extra pixels to repeat from right * @top_rpt: Number of extra lines to repeat from top * @btm_rpt: Number of extra lines to repeat from bottom */ struct sde_drm_pix_ext_v1 { /* * Number of pixels ext in left, right, top and bottom direction * for all color components. */ int32_t num_ext_pxls_lr[SDE_MAX_PLANES]; int32_t num_ext_pxls_tb[SDE_MAX_PLANES]; /* * Number of pixels needs to be overfetched in left, right, top * and bottom directions from source image for scaling. */ int32_t left_ftch[SDE_MAX_PLANES]; int32_t right_ftch[SDE_MAX_PLANES]; int32_t top_ftch[SDE_MAX_PLANES]; int32_t btm_ftch[SDE_MAX_PLANES]; /* * Number of pixels needs to be repeated in left, right, top and * bottom directions for scaling. */ int32_t left_rpt[SDE_MAX_PLANES]; int32_t right_rpt[SDE_MAX_PLANES]; int32_t top_rpt[SDE_MAX_PLANES]; int32_t btm_rpt[SDE_MAX_PLANES]; }; /** * struct sde_drm_scaler_v1 - version 1 of struct sde_drm_scaler * @lr: Pixel extension settings for left/right * @tb: Pixel extension settings for top/botton * @init_phase_x: Initial scaler phase values for x * @phase_step_x: Phase step values for x * @init_phase_y: Initial scaler phase values for y * @phase_step_y: Phase step values for y * @horz_filter: Horizontal filter array * @vert_filter: Vertical filter array */ struct sde_drm_scaler_v1 { /* * Pix ext settings */ struct sde_drm_pix_ext_v1 pe; /* * Phase settings */ int32_t init_phase_x[SDE_MAX_PLANES]; int32_t phase_step_x[SDE_MAX_PLANES]; int32_t init_phase_y[SDE_MAX_PLANES]; int32_t phase_step_y[SDE_MAX_PLANES]; /* * Filter type to be used for scaling in horizontal and vertical * directions */ uint32_t horz_filter[SDE_MAX_PLANES]; uint32_t vert_filter[SDE_MAX_PLANES]; }; /** * struct sde_drm_de_v1 - version 1 of detail enhancer structure * @enable: Enables/disables detail enhancer * @sharpen_level1: Sharpening strength for noise * @sharpen_level2: Sharpening strength for context * @clip: Clip coefficient * @limit: Detail enhancer limit factor * @thr_quiet: Quite zone threshold * @thr_dieout: Die-out zone threshold * @thr_low: Linear zone left threshold * @thr_high: Linear zone right threshold * @prec_shift: Detail enhancer precision * @adjust_a: Mapping curves A coefficients * @adjust_b: Mapping curves B coefficients * @adjust_c: Mapping curves C coefficients */ struct sde_drm_de_v1 { uint32_t enable; int16_t sharpen_level1; int16_t sharpen_level2; uint16_t clip; uint16_t limit; uint16_t thr_quiet; uint16_t thr_dieout; uint16_t thr_low; uint16_t thr_high; uint16_t prec_shift; int16_t adjust_a[SDE_MAX_DE_CURVES]; int16_t adjust_b[SDE_MAX_DE_CURVES]; int16_t adjust_c[SDE_MAX_DE_CURVES]; }; /* * Scaler configuration flags */ /* Disable dynamic expansion */ #define SDE_DYN_EXP_DISABLE 0x1 #define SDE_DRM_QSEED3LITE #define SDE_DRM_QSEED4 /** * struct sde_drm_scaler_v2 - version 2 of struct sde_drm_scaler * @enable: Scaler enable * @dir_en: Detail enhancer enable * @pe: Pixel extension settings * @horz_decimate: Horizontal decimation factor * @vert_decimate: Vertical decimation factor * @init_phase_x: Initial scaler phase values for x * @phase_step_x: Phase step values for x * @init_phase_y: Initial scaler phase values for y * @phase_step_y: Phase step values for y * @preload_x: Horizontal preload value * @preload_y: Vertical preload value * @src_width: Source width * @src_height: Source height * @dst_width: Destination width * @dst_height: Destination height * @y_rgb_filter_cfg: Y/RGB plane filter configuration * @uv_filter_cfg: UV plane filter configuration * @alpha_filter_cfg: Alpha filter configuration * @blend_cfg: Selection of blend coefficients * @lut_flag: LUT configuration flags * @dir_lut_idx: 2d 4x4 LUT index * @y_rgb_cir_lut_idx: Y/RGB circular LUT index * @uv_cir_lut_idx: UV circular LUT index * @y_rgb_sep_lut_idx: Y/RGB separable LUT index * @uv_sep_lut_idx: UV separable LUT index * @de: Detail enhancer settings * @dir_weight: Directional Weight * @unsharp_mask_blend: Unsharp Blend Filter Ratio * @de_blend: Ratio of two unsharp mask filters * @flags: Scaler configuration flags */ struct sde_drm_scaler_v2 { /* * General definitions */ uint32_t enable; uint32_t dir_en; /* * Pix ext settings */ struct sde_drm_pix_ext_v1 pe; /* * Decimation settings */ uint32_t horz_decimate; uint32_t vert_decimate; /* * Phase settings */ int32_t init_phase_x[SDE_MAX_PLANES]; int32_t phase_step_x[SDE_MAX_PLANES]; int32_t init_phase_y[SDE_MAX_PLANES]; int32_t phase_step_y[SDE_MAX_PLANES]; uint32_t preload_x[SDE_MAX_PLANES]; uint32_t preload_y[SDE_MAX_PLANES]; uint32_t src_width[SDE_MAX_PLANES]; uint32_t src_height[SDE_MAX_PLANES]; uint32_t dst_width; uint32_t dst_height; uint32_t y_rgb_filter_cfg; uint32_t uv_filter_cfg; uint32_t alpha_filter_cfg; uint32_t blend_cfg; uint32_t lut_flag; uint32_t dir_lut_idx; /* for Y(RGB) and UV planes*/ uint32_t y_rgb_cir_lut_idx; uint32_t uv_cir_lut_idx; uint32_t y_rgb_sep_lut_idx; uint32_t uv_sep_lut_idx; /* * Detail enhancer settings */ struct sde_drm_de_v1 de; uint32_t dir_weight; uint32_t unsharp_mask_blend; uint32_t de_blend; uint32_t flags; }; /* Number of dest scalers supported */ #define SDE_MAX_DS_COUNT 2 /* * Destination scaler flag config */ #define SDE_DRM_DESTSCALER_ENABLE 0x1 #define SDE_DRM_DESTSCALER_SCALE_UPDATE 0x2 #define SDE_DRM_DESTSCALER_ENHANCER_UPDATE 0x4 #define SDE_DRM_DESTSCALER_PU_ENABLE 0x8 /** * struct sde_drm_dest_scaler_cfg - destination scaler config structure * @flags: Flag to switch between mode for destination scaler * refer to destination scaler flag config * @index: Destination scaler selection index * @lm_width: Layer mixer width configuration * @lm_height: Layer mixer height configuration * @scaler_cfg: The scaling parameters for all the mode except disable * Userspace pointer to struct sde_drm_scaler_v2 */ struct sde_drm_dest_scaler_cfg { uint32_t flags; uint32_t index; uint32_t lm_width; uint32_t lm_height; uint64_t scaler_cfg; }; /** * struct sde_drm_dest_scaler_data - destination scaler data struct * @num_dest_scaler: Number of dest scalers to be configured * @ds_cfg: Destination scaler block configuration */ struct sde_drm_dest_scaler_data { uint32_t num_dest_scaler; struct sde_drm_dest_scaler_cfg ds_cfg[SDE_MAX_DS_COUNT]; }; /* * Define constants for struct sde_drm_csc */ #define SDE_CSC_MATRIX_COEFF_SIZE 9 #define SDE_CSC_CLAMP_SIZE 6 #define SDE_CSC_BIAS_SIZE 3 /** * struct sde_drm_csc_v1 - version 1 of struct sde_drm_csc * @ctm_coeff: Matrix coefficients, in S31.32 format * @pre_bias: Pre-bias array values * @post_bias: Post-bias array values * @pre_clamp: Pre-clamp array values * @post_clamp: Post-clamp array values */ struct sde_drm_csc_v1 { int64_t ctm_coeff[SDE_CSC_MATRIX_COEFF_SIZE]; uint32_t pre_bias[SDE_CSC_BIAS_SIZE]; uint32_t post_bias[SDE_CSC_BIAS_SIZE]; uint32_t pre_clamp[SDE_CSC_CLAMP_SIZE]; uint32_t post_clamp[SDE_CSC_CLAMP_SIZE]; }; /** * struct sde_drm_color - struct to store the color and alpha values * @color_0: Color 0 value * @color_1: Color 1 value * @color_2: Color 2 value * @color_3: Color 3 value */ struct sde_drm_color { uint32_t color_0; uint32_t color_1; uint32_t color_2; uint32_t color_3; }; /* Total number of supported dim layers */ #define SDE_MAX_DIM_LAYERS 7 /* SDE_DRM_DIM_LAYER_CONFIG_FLAG - flags for Dim Layer */ /* Color fill inside of the rect, including border */ #define SDE_DRM_DIM_LAYER_INCLUSIVE 0x1 /* Color fill outside of the rect, excluding border */ #define SDE_DRM_DIM_LAYER_EXCLUSIVE 0x2 /** * struct sde_drm_dim_layer - dim layer cfg struct * @flags: Refer SDE_DRM_DIM_LAYER_CONFIG_FLAG for possible values * @stage: Blending stage of the dim layer * @color_fill: Color fill for dim layer * @rect: Dim layer coordinates */ struct sde_drm_dim_layer_cfg { uint32_t flags; uint32_t stage; struct sde_drm_color color_fill; struct drm_clip_rect rect; }; /** * struct sde_drm_dim_layer_v1 - version 1 of dim layer struct * @num_layers: Numer of Dim Layers * @layer: Dim layer user cfgs ptr for the num_layers */ struct sde_drm_dim_layer_v1 { uint32_t num_layers; struct sde_drm_dim_layer_cfg layer_cfg[SDE_MAX_DIM_LAYERS]; }; /* Writeback Config version definition */ #define SDE_DRM_WB_CFG 0x1 /* SDE_DRM_WB_CONFIG_FLAGS - Writeback configuration flags */ #define SDE_DRM_WB_CFG_FLAGS_CONNECTED (1<<0) /** * struct sde_drm_wb_cfg - Writeback configuration structure * @flags: see DRM_MSM_WB_CONFIG_FLAGS * @connector_id: writeback connector identifier * @count_modes: Count of modes in modes_ptr * @modes: Pointer to struct drm_mode_modeinfo */ struct sde_drm_wb_cfg { uint32_t flags; uint32_t connector_id; uint32_t count_modes; uint64_t modes; }; #define SDE_MAX_ROI_V1 4 /** * struct sde_drm_roi_v1 - list of regions of interest for a drm object * @num_rects: number of valid rectangles in the roi array * @roi: list of roi rectangles */ struct sde_drm_roi_v1 { uint32_t num_rects; struct drm_clip_rect roi[SDE_MAX_ROI_V1]; }; /** * Define extended power modes supported by the SDE connectors. */ #define SDE_MODE_DPMS_ON 0 #define SDE_MODE_DPMS_LP1 1 #define SDE_MODE_DPMS_LP2 2 #define SDE_MODE_DPMS_STANDBY 3 #define SDE_MODE_DPMS_SUSPEND 4 #define SDE_MODE_DPMS_OFF 5 /** * sde recovery events for notifying client */ #define SDE_RECOVERY_SUCCESS 0 #define SDE_RECOVERY_CAPTURE 1 #define SDE_RECOVERY_HARD_RESET 2 #endif /* _SDE_DRM_H_ */